Monthly Archives: October 2016

Install 32bit AutoCAD Architecture 2014 on Windows 7, Windows 8 and Windows 10

Posted on by

NOTE: This blog post specifically solves issues related to these error messages on installation…

  • “This operating system is not supported by AutoCAD® Architecture® 2014”
  • “You cannot install this product on the current operating system”
  • “You are attempting to use a 32-bit installer on a 64-bit operating system”
  • “This is a 32-bit AutoCAD® Architecture® 2014. It cannot be installed on 64-bit Windows”

Installing AutoCAD Architecture 2014 (ADT 2014) 32bit on Windows 7, Windows 8, Windows 8.1 or Windows 10 64bit can be very easily defined in these short steps…

NOTE: These steps do not bypass normal Autodesk licensing/authorization, you should expect to use your own serial numbers in the normal way.

  1. Obtain your copy of the Longbow Converter here
  2. If you have CDs (if not check (3) below):
    1. Using Windows Explorer, copy Disk 1 of your AutoCAD Architecture 2014 CD to your hard drive, to a folder path c:\Autodesk\ADT2014
    2. If you have more CD’s, copy them all directly over the top of Disk 1, overwrite all files in your previously copied c:\Autodesk\ADT2014 folder
  3. If you have a single self extracting exe downloaded from Autodesk called something like AutoCAD_Arch_2014_English_Win_32_64bit_en-us_Setup.exe
    1. Simply run the exe, it will ask to unzip to a folder inside of c:\Autodesk, make a note of the folder for later use (we’ll refer to it from here as c:\Autodesk\ADT2014), now click OK. Wait until all of the files have extracted, when they do, the AutoCAD Architecture 2014 setup will automatically launch – simply close it and move to the next step.
  4. Now, start the Longbow Converter tool, select the 1st tab, pick the c:\Autodesk\ADT2014 folder, and click the Convert button.
  5. Once the conversion process is complete, click Install/Run Setup to start setup. Simply install as normal.
    1. Once installed, we recommend you disable the AutoCAD Communication Center/InfoCenter toolbar as it uses a lot of memory, causes slow startup and most people don’t use it anyway!
  6. Now you can happily run your AutoCAD Architecture 2014 32bit on Windows 7, Windows 8, Windows 8.1 and Windows 10!

Troubleshooting:

– If your AutoCAD crashes while interacting with the Ribbon click here

– If you are unable to activate your product, or the activation process crashes:

– If you have crashing problems using the File->Open or File->Save dialogs inside of AutoCAD please read this blog entry on the File->Open or File->Save Crash in AutoCAD

Copyright 2014 (c) Longbow Software

Install Autodesk Architectural Desktop 3.3 on Windows 7, Windows 8 and Windows 10

Posted on by

Follow these instructions to solve issues around installing/running your old AutoCAD Architecture 3.3 (ADT 2002) on newer versions of 64bit Windows 7, Windows 8 and Windows 10

How to install AutoCAD ADT 3.3 

  1. Obtain your purchased copy of the Longbow Converter here
  2. Start the Longbow Converter tool
    1. Insert your AutoCAD CD into your CDRom drive
    2. Select the 2nd tab named “Old AutoCAD Installer Reviver“
    3. Using the “…” button, path the to your AutoCAD CD
    4. Click “Run Old Installer”
      1. Read and follow all the prompts
      2. Once the AutoCAD setup starts, stop and read the next step…
  3. In the AutoCAD setup program, navigate through each setup dialog as normal, with these exceptions…
    1. When you arrive at the installation folder path setup dialog…
      1. **it’s vitally important to make sure you install to c:\adt2002 (not Program Files (x86)\AutoCAD Architecture 3.3)**.
    2. Once installed
      1. Do not reboot if asked to do so
      2. Make sure to fully close the setup program when the installation is complete.
      3. Back in the Converter app and make sure it’s completed the final stage of processing using the “Old AutoCAD Program Reviver” tab
  4. Finally, it’s important to now reboot your PC and then install the service pack update below

Install AutoCAD Architecture 3.3 Sp2

To install the sp for your AutoCAD…
  1. Download your AutoCAD ADT 3.3 Sp2
  2. Copy the service pack exe installer to folder path c:\Autodesk\sp
  3. Start the Converter App
    1. select the 3rd tab named “Old AutoCAD Program Reviver“
    2. Using the “. . .” button, pick the c:\Autodesk\sp folder
    3. click “Fix Old Program“.
  4. Now you can run the service pack exe installer from Windows explorer as normal

Last step…
We highly recommend that you disable the “Today” start page page that pops up when ADT starts…. Right click the command line->Options->Preferences->System->Startup:Do not show a startup dialog

Troubleshooting

Copyright 2019 (c) Longbow Software

Install 32bit AutoCAD 2017 on Windows 7, Windows 8 and Windows 10

Posted on by

These instructions solve issues around installing/running your old AutoCAD 2017 on newer versions of 64bit Windows 7, Windows 8 and Windows 10. Some common issues are error messages like these…

  • “This operating system is not supported by AutoCAD® 2017”
  • “You cannot install this product on the current operating system”
  • “You are attempting to use a 32-bit installer on a 64-bit operating system”
  • “This is a 32-bit AutoCAD® 2017. It cannot be installed on 64-bit Windows”

You can automatically solve these problems using our Longbow Converter App, it fixes and manages the AutoCAD 2017 installation so that you can be up and running again… Follow these instructions:

How to install AutoCAD 2017

  1. Obtain your purchased copy of the Longbow Converter here
  2. Start the Converter App and note the user interface
  3. Select the 1st tab named “AutoCAD 32bit Installer Converter“
    1. Using the “. . .” button, selection your AutoCAD installation CD
    2. Next, click the “Convert“ button and follow instructions
  4. Once the conversion process is complete
    1. click Install/Run Setup to start setup
    2. Simply install as normal, remembering to…
      1. Close the setup program when the installation is complete.
      2. Back in the Converter app and make sure it has completed the final stage of processing using the “Old AutoCAD Program Reviver” tab
  5. Now run your AutoCAD as normal

Troubleshooting

– If your AutoCAD starts with a blank white screen…

  • Try turning down your screen resolution, if this doesn’t help…
    • from the Converter tool, pick the Tools->Clean Compatibility settings

– If you are unable to activate your product, or the activation process crashes:

– If you have crashing problems using the File->Open or File->Save dialogs inside of AutoCAD please read this blog entry on the File->Open or File->Save Crash in AutoCAD

Copyright 2019 (c) Longbow Software

Installing 32bit AutoCAD LT 2014 on Windows 7, Windows 8 and Windows 10

Posted on by

NOTE: This blog post specifically solves issues related to these error messages on installation…

  • “This operating system is not supported by AutoCAD LT®”
  • “You cannot install this product on the current operating system”
  • “You are attempting to use a 32-bit installer on a 64-bit operating system”
  • “This is a 32-bit AutoCAD LT® 2014. It cannot be installed on 64-bit Windows”

NOTE: These steps do not bypass normal Autodesk licensing/authorization, you should expect to use your own serial numbers in the normal way.

Installing AutoCAD LT 2014 32bit on Windows 7, Windows 8, Windows 8.1 or Windows 10 64bit can be very easily defined in these short steps.

  1. Obtain your copy of the Longbow Converter here
  2. If you have CDs (if not check (3) below):
    1. Using Windows Explorer, copy Disk 1 of your AutoCAD LT 2014 CD to your hard drive, to a folder path c:\Autodesk\AutoCADLT2014
    2. If you have more CD’s, copy them all directly over the top of Disk 1, overwrite all files in your previously copied c:\Autodesk\AutoCADLT2014 folder
  3. If you have a single self extracting exe downloaded from Autodesk called something like AutoCAD_LT_2014_English_Win_32bit.exe
    1. Simply run the exe, it will ask to unzip to a folder inside of c:\Autodesk, make a note of the folder for later use (we’ll refer to it from here as c:\Autodesk\AutoCADLT2014), now click OK. Wait until all of the files have extracted, when they do, the AutoCAD LT 2014 setup will automatically launch – simply close it and move to the next step.
  4. Now, start the Longbow Converter tool, select the 1st tab named ‘AutoCAD 32bit Installer Converter‘
    1. pick the c:\Autodesk\AutoCADLT2014 folder
    2. click the ‘Convert‘ button.
  5. Once the conversion process is complete
    1. Click ‘Install/Run Setup‘ to start setup
    2. Install as normal.
  6. Windows 8, Windows 8.1 and Windows 10 users: Once the installation process is complete…
    1. go back to the Converter, select the 3rd tab named ‘Old AutoCAD Program Reviver‘
    2. Pick the newly installed C:\Program Files (x86)\Autodesk\AutoCAD LT 2014 folder
    3. Click ‘Fix Old Program‘.
  7. Now you can happily run your AutoCAD LT 2014 32bit on Windows 7, Windows 8 and Windows 10!

Troubleshooting:

– If your AutoCAD crashes while interacting with the Ribbon click here

– If you are unable to activate your product, or the activation process crashes:

– If you have crashing problems using the File->Open or File->Save dialogs inside of AutoCAD please read this blog entry on the File->Open or File->Save Crash in AutoCAD

Copyright 2016 (c) Longbow Software

Install 32bit AutoCAD Electrical 2010 on Windows 7, Windows 8 and Windows 10

Posted on by

NOTE: This blog post specifically solves issues related to these error messages on installation…

  • “This operating system is not supported by AutoCAD® Electrical® 2010”
  • “You cannot install this product on the current operating system”
  • “You are attempting to use a 32-bit installer on a 64-bit operating system”
  • “This is a 32-bit AutoCAD® Electrical® 2010. It cannot be installed on 64-bit Windows”

…Also, hung “Merging content…” message while installing…

NOTE: These steps do not bypass normal Autodesk licensing/authorization, you should expect to use your own serial numbers in the normal way.

Installing 32bit AutoCAD Electrical 2010 on Windows 7, Windows 8, Windows 8.1 or Windows 10 64bit can be very easily defined in these short steps.

  1. First of all, you need V9.20 of the Longbow Converter (or newer) – obtain the latest version of the Longbow Converter here
  2. If you have CDs (if not skip to step 3 below) you must copy ALL CDs to your hard drive using the following instructions…
    1. Using Windows Explorer, copy Disk 1 of your AutoCAD Electrical 2010 CD to your hard drive, to a folder path c:\Autodesk\AutoCADE2010
    2. If you have more CD’s, copy them all directly over the top of Disk 1, overwrite all files in your previously copied c:\Autodesk\AutoCADE2010 folder
  3. If you have a single self extracting exe downloaded from Autodesk
    1. Run the exe, it will ask to unzip to a folder inside of c:\Autodesk, make a note of the folder name created for later use (we’ll refer to it from here as c:\Autodesk\AutoCADE2010), now click OK.
    2. Wait until all of the files have extracted, when they do, the AutoCAD Electrical 2010 setup will automatically launch – simply close it and move to the next step.
  4. Next start the Longbow Converter tool (V9.20 or newer)
    1. select the 1st tab named “AutoCAD 32bit Installer Converter“
    2. Pick the c:\Autodesk\AutoCADE2010 folder (where you copied the CDs to)
    3. then click the “Convert…“ button
  5. Once the conversion process is complete
    1. click Install/Run Setup to start setup.
    2. Install as normal, EXCEPT – you must install to “c:\AcadE2010” (<<< the exact text, anything else will fail!) instead of c:\Program Files (x86)\AutoCAD Electrical.
    3. NOTE: Be sure to download any updates that the setup offers you.
  6. Windows 8 users: Once the installation process is complete, go back to the Converter, select the 3rd tab, pick the newly installed C:\Program Files (x86)\Autodesk\Acade 2010 folder, then click Fix Old Program
  7. Now you can happily run your AutoCAD 2010 32bit on Windows 7, Windows 8, Windows 8.1 and Windows 10.

Troubleshooting:

  1. If your installed AutoCAD is hanging on startup then read this post first AutoCAD Freezes on startup (AutoCAD visible but the menus don’t appear)
  2. if your AutoCAD hangs on startup (stuck at the “Checking License…” message, try installing the 32bit version of AutoCAD 2010 on 64bit Windows – we’ve actually found the 32bit AutoCAD 2010 running on 64bit Windows is much more stable and actually faster than the 64bit version of AutoCAD 2010.
  3. If your AutoCAD crashes while interacting with the Ribbon click here
  4. If you are unable to activate your product, or the activation process crashes:
    1. Try uninstalling the July 2014 Microsoft security update
    2. Try downgrading your Internet Explorer (IE) from version 11 to version 10 by following the instructions detailed here
  5. If you have crashing problems using the File->Open or File->Save dialogs inside of AutoCAD please read this blog entry on the File->Open or File->Save Crash in AutoCAD
  6. If your Windows hangs on startup after installing please refer to this help blog
Copyright 2016 (c) Longbow Software